OUR

PRODUCTS

COMPACT DETAILS

Flexibility of Design and Space Sacing.

Wide Choice Of Colours

Colours Fast and Durable

Impact Resistant

Burn Resistant

Water Resistant

Scratch Resistant

Graffiti Resistant

Chemical Resistant

COMPACT CLADDING

  • INTERNAL CLADDING
  • EXTERNAL CLADDING

INTERNAL CLADDING

Internal Wall Cladding Solution is a High Pressure Compact Laminate based wall protection system, this product is primarily used for internal application i.e. protecting the internal walls of a building from various kinds of damage, along with enhancing the aesthetics of the interior

EXTERNAL CLADDING

The idea of interior designing has taken a whole new turn. One irony being that designing is no more confined to interiors, thus, the evolution of the term ‘exterior designing’. Welcome to the world.

From inspiration to application, each and every aspect of ‘exterior designing’ is different. While weather plays a crucial role, it is aesthetics that drive the concept.

Imagine8 Exterior Cladding has been conceived taking all aspects into consideration. The laminates are manufactured in lamination presses under high pressure and temperature. The special quality resins provide effective weather protection. Be it sun, rain or snow, the character of the laminates is not going to be lost. Be assured of shape, colour and durability.

Imagine8 also brings to you a unique ventilated facade system, which allows water, moisture or any other natural agent to find their way through the laminate installation.

The choices that you have in Imagine8 laminate designs might make it difficult for you to decide. From patterns inspired by nature, to designs complementing your interior , from plain and solid hues to completely abstract construct, you have them all.

URINAL PARTITION

General

IMAGINE8 supply and install UMP System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The UMP Panel partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

UMP Panel

All UMP Panel shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 4 S.S. Right angle support affixed to the Wall.

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel 4 no’s Right Angle

Stainless Screw

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.
Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE -UMP SYSTEM

Dimension

Size of Cubicle :450 – 400 mm (W) X 900 mm(H)

The recommended restroom cubicle size is 450 ~ 500mm X 900 ~ 1200mm (W x H)

Height of compartment measured from Bottom Finished Floor is 1300mm (inclusive floor clearance of 400mm).

Size shall be between 450 mm ~ 500mm in width

Overall Height Of Cubicle : 1300 mm (Including bottom Gap of 400mm)

Customized Overall Height Of Cubicle : 1200 mm (Including bottom Gap of400mm)

RESTROOM CUBICAL

  • LEO NYLON SERIES
  • LEO SS SERIES
  • VEGA SS SERIES
  • VEGA 12MM CH SERIES
  • VEGA 18MM CH SERIES
  • REGEL SERIES
  • CAPELLA HUNG SERIES
  • IDOOR

LEO NYLON SERIES

General

IMAGINE8 supply and install LEO Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of nylon and all hardware/fitting shall be made of anodized Aluminum. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon Hinges (4 for physical handicap restroom) affixed to the pilaster, completed with Nylon Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with Anodized Aluminum Door Stopper profile (incorporated with Rubber Lining to dampen noise) affixed on one vertical side and completed with Nylon Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using Nylon Adjustable Leg with Anodized Aluminum Top Rail for stability. The floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with Anodized Aluminum U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system, recommends that the length shall be 1500mm not exceed 1800mm.

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Anodized Aluminum +Nylon Accessories.

Top Rail

Anodized Aluminum Top Rail Channel shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

 Nylon Door Knob.

 Nylon Thumb-turn with occupancy indicator.

 Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Nylon Hinges with 3 No’s of standard, gravity-to-open or gravity-to-close.

 Nylon Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE -LEO NYLON SERIES

Leo Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2000 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2030 ~ 2100mm (W x D x H)

Height of restroom compartment measured from top of the pilaster is 2030mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2000 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2200 mm (Including bottom Gap of 80 ~ 150mm)

LEO SS SERIES

General

IMAGINE8 supply and install LEO Stainless steel Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of anodized Aluminum o. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for accessible restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Stainless Steel Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with anodized Aluminum Door Stopper profile (incorporated with Rubber Lining to dampen noise) affixed on one vertical side and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using Stainless Steel Adjustable Leg with threaded rod inserts for stability. The floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with anodized Aluminum U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system, recommends that the length shall be 1500mm not exceed 1800mm.

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Anodized Aluminum+ Stainless Steel Accessories

Top Rail

Anodized Aluminum Top Rail Channel, shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE - LEO STAINLESS STEEL SERIES

Leo Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2000 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2030 ~ 2200mm **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

Overall Height Of Cubicle : 2030 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2200 mm (Including bottom Gap of 80 ~ 150mm)

VEGA SS SERIES

General

IMAGINE8 supply and install VEGA Stainless steel Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single color, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap Restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with Stainless Steel Door Stopper profile (incorporated with Rubber Lining to dampen noise) affixed on one vertical side and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using Stainless Steel Adjustable Leg with threaded rod inserts for stability. The floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with anodized Aluminium Stainless Steel U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system, recommends that the length shall be 1500mm not exceed 1800mm.

Accessories

Stainless Steel Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE - VEGA STAINLESS STEEL SERIES

VEGA Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2000 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2030 ~ 2200mm **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

Overall Height Of Cubicle : 2030 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2200 mm (Including bottom Gap of 80 ~ 150mm)

VEGA 12MM CH SERIES

General

IMAGINE8supply and install VEGA 12 MM CH Restroom Cubicle System, which is highly resistant against water and impact

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single color, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap Restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with chamfered edge and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using U-Channel and covered with Stainless Steel Channel .Pilasters will be routered at its vertical ends to facilitate closure of doors. The floor clearance is 10mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends to the wall and pilaster for ultimate stability of the system, IMAGINE8 recommends that the length shall be 1500 mm not exceed 1800mm.

Accessories

Stainless Steel Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE - VEGA 12mm CH STAINLESS STEEL SERIES

VAGA 12mm CH Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2100 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2100 **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 10mm)..

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2100 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 3000 mm (Including bottom Gap of 10mm)

VEGA 18MM CH SERIES

General

IMAGINE8supply and install VEGA 18 MM CH Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 18mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single color, 18mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap Restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 18mm thick HPL compact board with chamfered edge and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using U-Channel and covered with Stainless Steel Channel .Pilasters will be routered at its vertical ends to facilitate closure of doors. The floor clearance is 10mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm or 18mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends to the wall and pilaster for ultimate stability of the system, IMAGINE8 recommends that the length shall be 1500 mm not exceed 1800mm.

Accessories

Stainless Steel Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

 

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE - VEGA 18mm CH STAINLESS STEEL SERIES

VEGA 18mm CH Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2100 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2100 **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 10mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2100 mm (Including bottom Gap of 10mm)

Customised Overall Height Of Cubicle : 3000 mm (Including bottom Gap of 10mm)

REGEL SERIES

General

IMAGINE8 supply and install RIGEL HUNG Stainless Steel Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Nylon polyamide grade or Stainless Steel and all hardware/fitting shall be made of anodized Aluminium or Stainless Steel. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Equivalent to Indian standard IS-2046) (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single Colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon or Stainless Steel Hinges affixed to the pilaster, completed with Nylon or Stainless Steel Coat Hook & Nylon or Stainless Stee Door Knob. Doors will Supported with Channel at its vertical ends & incorporated with Rubber sponge.

Pilasters

All pilasters shall be of same Colour as doors, 12mm thick HPL Compact board with chamfered edge, completed with Nylon or Stainless Steel Thumb turn for Locking Doors. The pilaster is slotted & affixed to the top rail and secured from the top of the Top Rail. The Floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same Colour as per door, 12mm thick HPL compact with anodized aluminum or Stainless Steel U-channel, affixed at its ends (to the wall & pilaster) For ultimate stability of the system IMAGINE8 Recommend that the length standard 1500mm & Max 1800mm

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Top Rail

Aluminium Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Stainless Steel Or Nylon Door Knob.

 Stainless Steel Or Nylon Thumbturn with occupancy indicator.

 Stainless Steel Or Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Or Nylon Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

Stainless Steel Or Nylon Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE - RIGEL HUNG STAINLESS STEEL SERIES OR NYLON

RIGEL Hung Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2090 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2090 **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 10mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2090 mm (Including bottom Gap of 10mm)

Customised Overall Height Of Cubicle : 3000 mm** (Including bottom Gap of 10mm)

CAPELLA HUNG SERIES

General

IMAGINE8supply and install Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 18mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges. HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 18mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap restroom) affixed to the pilaster, completed with S.S. Coat Hook and S.S.Lock Set. Doors will be routered at its vertical ends and incorporated with Rubber Sponge.

Pilasters

All pilasters shall be of same colour as doors, 18mm thick HPL compact board with chamfered. The pilaster affixed to the Rectangular Plate, and then fixed to the top rail. The assembled parts will then be beautifully concealed by the Stainless Steel Box Up construction. Pilasters will be routered at its vertical ends to facilitate closure of doors. The visible height from finished floor level (FFL) to false ceiling is 2550mm, included a floor clearance of 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm Or 18mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system IMAGINE8 Recommend that the length standard 1500mm to Max 1800mm

Accessories

Heavy-duty Aluminium Channel, act as top rail shall be secured to the wall using Steel Wall Bracket.

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob.

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

SStainless Steel Box Up with height 100 mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE -CAPELLA HUNG SERIES

Compartment’s Dimension

Size of Cubicle :900mm (W) X 1500 mm (D)X 2550 mm(H

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X 2550 ~ 3000mm (W x D x H).

Visible height of restroom compartment measured from FFL to false ceiling is 2550mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2550 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 3000 mm (Including bottom Gap of 10mm)

IDOOR

General

IMAGINE8 supply and install Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of nylon and all hardware/fitting shall be made of anodized Aluminium. The door, partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon Hinges (4 for physical handicap restroom) affixed to the Anodized Aluminum D Post , completed with Nylon Coat Hook, Nylon Thumb-turn with occupancy indicator and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 18mm thick HPL compact board with chamfered. The pilaster affixed to the Rectangular Plate, and then fixed to the top rail. The assembled parts will then be beautifully concealed by the Stainless Steel Box Up construction. Pilasters will be routered at its vertical ends to facilitate closure of doors. The visible height from finished floor level (FFL) to false ceiling is 2550mm, included a floor clearance of 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm Or 18mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system IMAGINE8 Recommend that the length standard 1500mm to Max 1800mm

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Anodized Aluminum + Nylon Accessories.

 Nylon Door Knob.

 Nylon Thumb-turn with occupancy indicator.

 Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Nylon Hinges with 3 No’s of standard, gravity-to-open or gravity-to-close

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE -I- DOOR SERIES

Compartment’s Dimension

Size of Cubicle :600mm (W) X 1980 mm(H)

The recommended restroom cubicle size is 600 ~ 900mm X 1980 ~ 2100mm (W x H).

Height of restroom compartment measured from top of the Pole is 1980mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 900mm in width

verall Height Of Cubicle : 1980 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2100 mm (Including bottom Gap of 80 ~ 150mm)

LEO NYLON SERIES

General

IMAGINE8 supply and install LEO Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of nylon and all hardware/fitting shall be made of anodized Aluminum. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon Hinges (4 for physical handicap restroom) affixed to the pilaster, completed with Nylon Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with Anodized Aluminum Door Stopper profile (incorporated with Rubber Lining to dampen noise) affixed on one vertical side and completed with Nylon Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using Nylon Adjustable Leg with Anodized Aluminum Top Rail for stability. The floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with Anodized Aluminum U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system, recommends that the length shall be 1500mm not exceed 1800mm.

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Anodized Aluminum +Nylon Accessories.

Top Rail

Anodized Aluminum Top Rail Channel shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

 Nylon Door Knob.

 Nylon Thumb-turn with occupancy indicator.

 Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Nylon Hinges with 3 No’s of standard, gravity-to-open or gravity-to-close.

 Nylon Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE -LEO NYLON SERIES

Leo Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2000 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2030 ~ 2100mm (W x D x H)

Height of restroom compartment measured from top of the pilaster is 2030mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2000 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2200 mm (Including bottom Gap of 80 ~ 150mm)

LEO NYLON SERIES

General

IMAGINE8 supply and install LEO Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of nylon and all hardware/fitting shall be made of anodized Aluminum. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon Hinges (4 for physical handicap restroom) affixed to the pilaster, completed with Nylon Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with Anodized Aluminum Door Stopper profile (incorporated with Rubber Lining to dampen noise) affixed on one vertical side and completed with Nylon Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using Nylon Adjustable Leg with Anodized Aluminum Top Rail for stability. The floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with Anodized Aluminum U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system, recommends that the length shall be 1500mm not exceed 1800mm.

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Anodized Aluminum +Nylon Accessories.

Top Rail

Anodized Aluminum Top Rail Channel shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

 Nylon Door Knob.

 Nylon Thumb-turn with occupancy indicator.

 Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Nylon Hinges with 3 No’s of standard, gravity-to-open or gravity-to-close.

 Nylon Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE -LEO NYLON SERIES

Leo Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2000 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2030 ~ 2100mm (W x D x H)

Height of restroom compartment measured from top of the pilaster is 2030mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2000 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2200 mm (Including bottom Gap of 80 ~ 150mm)

VEGA SS SERIES

General

IMAGINE8 supply and install VEGA Stainless steel Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single color, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap Restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with Stainless Steel Door Stopper profile (incorporated with Rubber Lining to dampen noise) affixed on one vertical side and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using Stainless Steel Adjustable Leg with threaded rod inserts for stability. The floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with anodized Aluminium Stainless Steel U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system, recommends that the length shall be 1500mm not exceed 1800mm.

Accessories

Stainless Steel Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE – VEGA STAINLESS STEEL SERIES

VEGA Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2000 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2030 ~ 2200mm **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

Overall Height Of Cubicle : 2030 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2200 mm (Including bottom Gap of 80 ~ 150mm)

VEGA 12MM CH SERIES

General

IMAGINE8supply and install VEGA 12 MM CH Restroom Cubicle System, which is highly resistant against water and impact

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single color, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap Restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 12mm thick HPL compact board with chamfered edge and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using U-Channel and covered with Stainless Steel Channel .Pilasters will be routered at its vertical ends to facilitate closure of doors. The floor clearance is 10mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends to the wall and pilaster for ultimate stability of the system, IMAGINE8 recommends that the length shall be 1500 mm not exceed 1800mm.

Accessories

Stainless Steel Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE – VEGA 12mm CH STAINLESS STEEL SERIES

VAGA 12mm CH Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2100 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2100 **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 10mm)..

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2100 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 3000 mm (Including bottom Gap of 10mm)

VEGA 18MM CH SERIES

General

IMAGINE8supply and install VEGA 18 MM CH Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 18mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single color, 18mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap Restroom) affixed to the pilaster, completed with Stainless Steel Coat Hook and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 18mm thick HPL compact board with chamfered edge and completed with Stainless Steel Thumb turn for locking doors. Colours different from doors are available upon request. The pilaster shall be anchored to the floor using U-Channel and covered with Stainless Steel Channel .Pilasters will be routered at its vertical ends to facilitate closure of doors. The floor clearance is 10mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm or 18mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends to the wall and pilaster for ultimate stability of the system, IMAGINE8 recommends that the length shall be 1500 mm not exceed 1800mm.

Accessories

Stainless Steel Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

 

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob .

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

 Stainless Steel Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE – VEGA 18mm CH STAINLESS STEEL SERIES

VEGA 18mm CH Stainless Steel Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2100 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2100 **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 10mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2100 mm (Including bottom Gap of 10mm)

Customised Overall Height Of Cubicle : 3000 mm (Including bottom Gap of 10mm)

REGEL SERIES

General

IMAGINE8 supply and install RIGEL HUNG Stainless Steel Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Nylon polyamide grade or Stainless Steel and all hardware/fitting shall be made of anodized Aluminium or Stainless Steel. The door, pilasters & intermediate partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C). HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Equivalent to Indian standard IS-2046) (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single Colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon or Stainless Steel Hinges affixed to the pilaster, completed with Nylon or Stainless Steel Coat Hook & Nylon or Stainless Stee Door Knob. Doors will Supported with Channel at its vertical ends & incorporated with Rubber sponge.

Pilasters

All pilasters shall be of same Colour as doors, 12mm thick HPL Compact board with chamfered edge, completed with Nylon or Stainless Steel Thumb turn for Locking Doors. The pilaster is slotted & affixed to the top rail and secured from the top of the Top Rail. The Floor clearance is 150mm.

Intermediate Partitions

All intermediate partitions shall be of same Colour as per door, 12mm thick HPL compact with anodized aluminum or Stainless Steel U-channel, affixed at its ends (to the wall & pilaster) For ultimate stability of the system IMAGINE8 Recommend that the length standard 1500mm & Max 1800mm

Accessories

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Top Rail

Aluminium Top Rail shall be section fixed onto the top of the pilaster for maximum strength, stability and alignment of the system.

Stainless Steel Or Nylon Door Knob.

 Stainless Steel Or Nylon Thumbturn with occupancy indicator.

 Stainless Steel Or Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Or Nylon Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

Stainless Steel Or Nylon Adjustable Leg with a working range from140mm to 160mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE – RIGEL HUNG STAINLESS STEEL SERIES OR NYLON

RIGEL Hung Series Compartment’s Dimension – Size of Cubicle :900mm (W) X 1500 mm (D)X 2090 mm(H)

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X2090 **(W x D x H)

Height of restroom compartment measured from top of the pilaster is 2000mm (inclusive floor clearance of 10mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2090 mm (Including bottom Gap of 10mm)

Customised Overall Height Of Cubicle : 3000 mm** (Including bottom Gap of 10mm)

CAPELLA HUNG SERIES

General

IMAGINE8supply and install Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of Stainless Steel and all hardware/fitting shall be made of Stainless Steel. The door, pilasters & intermediate partitions shall be 18mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges. HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 18mm thick HPL compact board with chamfered edge. Each will be supported by 3 Stainless Steel Hinges (4 for Physical Handicap restroom) affixed to the pilaster, completed with S.S. Coat Hook and S.S.Lock Set. Doors will be routered at its vertical ends and incorporated with Rubber Sponge.

Pilasters

All pilasters shall be of same colour as doors, 18mm thick HPL compact board with chamfered. The pilaster affixed to the Rectangular Plate, and then fixed to the top rail. The assembled parts will then be beautifully concealed by the Stainless Steel Box Up construction. Pilasters will be routered at its vertical ends to facilitate closure of doors. The visible height from finished floor level (FFL) to false ceiling is 2550mm, included a floor clearance of 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm Or 18mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system IMAGINE8 Recommend that the length standard 1500mm to Max 1800mm

Accessories

Heavy-duty Aluminium Channel, act as top rail shall be secured to the wall using Steel Wall Bracket.

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Stainless Steel Accessories.

Stainless Steel Door Knob.

 Stainless Steel Thumbturn with occupancy indicator.

 Stainless Steel Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Stainless Steel Hinges with 3 No’s of standard,gravity-to-open or gravity-to-close.

SStainless Steel Box Up with height 100 mm.

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.

 Product and solution proposal.

 Specification writing.

 Project estimation.

 CAD layout drawings.

 Delivery.

 Installation.

 After sales support.

 Warranty.

 Maintenance.

 Identification of the project requirement.

 Complementary products and services.

MODLE TYPE -CAPELLA HUNG SERIES

Compartment’s Dimension

Size of Cubicle :900mm (W) X 1500 mm (D)X 2550 mm(H

The recommended restroom cubicle size is 900 ~ 1000mm X 1500 ~ 1800mm X 2550 ~ 3000mm (W x D x H).

Visible height of restroom compartment measured from FFL to false ceiling is 2550mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 750mm in width.

verall Height Of Cubicle : 2550 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 3000 mm (Including bottom Gap of 10mm)

IDOOR

General

IMAGINE8 supply and install Restroom Cubicle System, which is highly resistant against water and impact.

Materials

All accessories shall be made of nylon and all hardware/fitting shall be made of anodized Aluminium. The door, partitions shall be 12mm thick High Pressure Laminates (HPL) Compact Board with chamfered edges.

Grade HPL compact board are manufactured from sheet of special Kraft & décor paper, impregnated with thermosetting synthetic resins which are together under heat & high pressure (110Kg/cm2 at temperature of about 150°C).HPL compact board has laminates on both sides with suede finishes melamine. The performance of the board is tested according to Standards EN438 (Boiling Water, Fire Rate, Impact, Stain, and Scratch)

Doors

All doors shall be of single colour, 12mm thick HPL compact board with chamfered edge. Each will be supported by 3 Nylon Hinges (4 for physical handicap restroom) affixed to the Anodized Aluminum D Post , completed with Nylon Coat Hook, Nylon Thumb-turn with occupancy indicator and Door Knob.

Pilasters

All pilasters shall be of same colour as doors, 18mm thick HPL compact board with chamfered. The pilaster affixed to the Rectangular Plate, and then fixed to the top rail. The assembled parts will then be beautifully concealed by the Stainless Steel Box Up construction. Pilasters will be routered at its vertical ends to facilitate closure of doors. The visible height from finished floor level (FFL) to false ceiling is 2550mm, included a floor clearance of 150mm.

Intermediate Partitions

All intermediate partitions shall be of same colour as door, 12mm Or 18mm thick HPL compact board with Stainless Steel U-channel, affixed at its ends (to the wall and pilaster). For ultimate stability of the system IMAGINE8 Recommend that the length standard 1500mm to Max 1800mm

Top Rail

Each Restroom cubicle will be equipped with the following accessories Standard – Anodized Aluminum + Nylon Accessories.

 Nylon Door Knob.

 Nylon Thumb-turn with occupancy indicator.

 Nylon Coat Hook with/without rubber stopper and allow load up to 15kg-20kg respectively.

 Nylon Hinges with 3 No’s of standard, gravity-to-open or gravity-to-close

IMAGINE8 Full Service concept

IMAGINE8 will assist in every stage of the project. Full service concept is your assurance for a successful completion and peace of mind in project development.

Full Service

 Design advisory.
 Product and solution proposal.
 Specification writing.
 Project estimation.
 CAD layout drawings.
 Delivery.
 Installation.
 After sales support.
 Warranty.
 Maintenance.
 Identification of the project requirement.
 Complementary products and services.

MODLE TYPE -I- DOOR SERIES

Compartment’s Dimension

Size of Cubicle :600mm (W) X 1980 mm(H)

The recommended restroom cubicle size is 600 ~ 900mm X 1980 ~ 2100mm (W x H).

Height of restroom compartment measured from top of the Pole is 1980mm (inclusive floor clearance of 150mm).

Door size shall be between 600 mm ~ 900mm in width

verall Height Of Cubicle : 1980 mm (Including bottom Gap of 150mm)

Customised Overall Height Of Cubicle : 2100 mm (Including bottom Gap of 80 ~ 150mm)

TECHNICAL DATA SHEET

SR. NO. PROPERTIES UNIT SPECIFICATION

BS EN 438-4
IMAGINE TYPICAL VALUES
1
Thickness
for 12mm

for 18mm
12 ± 0.6

18 ± 0.7
12 ± 0.6

18 ± 0.7
2
Flatness
mm / m, max, deviation
3.0
3.0 max
3
Resistance to surface wear, wear value
Rev.min.
350
370 max
4
Resistance to impact by large diameter ball
Drop Height, min, t ≥ 6mm
1800
2000
5
Resistance to scratching
Rating(min)
Smooth finishes
for 18mm

2
2

3
3
6
Resistance to dry heat at 180°c
a) Gloss
b) Other Finishes

Grade, min.
Grade, min.

3
4

4
5
7
Resistance to immersion in boiling water
a) Mass Increase
b) Thickness increase
c) Appearance
t ≥ 12mm
%, max.
%, max.
Grade, min.

2
2
3

0.8
1.0
4
8
Dimensional stability at elevated temparature(t ≥ 12mm)
(L) %, max.
(T) %, max.
0.3
0.6
0.2
0.4
9
Resistance to staining
a) Group 1 & 2
b) Group 3
Rating (min)
Grade, min.
Grade, min.

5
4

5
5
10
Resistanceto cigarette burns
Grade, min.
3
4
11
Resistance to crazing
Grade, min.
4
5
12
Resistance to steam / water vapour (texture finishes)
Grade, min.
4
5
13
Lightfastness (Xenon arc)
Grey scale rating
4 - 5
4 - 5
14
Flexural modulus
Stress Mpa (min)
9000
10000
15
Flatness
Stress Mpa (min)
80
90 max